-
The Checklist: What to Do on Every Burnham Service Call
-
Step 1: Confirm the boiler type before you touch anything
-
Step 2: Photograph the thermostat wiring before replacement
-
Step 3: Test the blower motor under load, not just visually
-
Step 4: Check the condensate trap and drain line on condensing models
-
Step 5: Inspect the heat exchanger and combustion chamber
-
Step 6: Verify gas pressure and check for leaks
-
Step 7: Check the expansion tank and system pressure
-
Step 8: Confirm warranty documentation and registration status
-
Step 9: Log everything and set the next service date
-
Step 1: Confirm the boiler type before you touch anything
-
Common Mistakes and Things to Watch For
If you're servicing Burnham gas boilers or condensing units—or you manage a team that does—this checklist is for you. I'm not going to give you a textbook overview of how boilers work. You already know that. What I'm giving you is the exact sequence I use on every Burnham call, refined over seven years of dispatch work, field coordination, and let's be honest, a few expensive screw-ups that I'd rather you avoid.
I handle service orders for a heating contractor that runs a lot of Burnham equipment—residential and commercial. Since 2017, I've personally made and documented enough mistakes to fill a small binder. The checklist below is the result. Nine steps. Follow them in order when you can.
The Checklist: What to Do on Every Burnham Service Call
Step 1: Confirm the boiler type before you touch anything
Burnham makes both conventional gas boilers and condensing boilers, and they don't share the same service profile. The condensing units have a secondary heat exchanger, a condensate trap, and PVC venting. The conventional units don't.
In my first year (2017), I made the classic assumption mistake: I walked into a service call, saw "Burnham" on the data plate, and started looking for a flue damper that didn't exist. Forty-five minutes later, a senior tech pointed out I was working on a condensing unit. The damper was never there. That error cost the company about $180 in billable time and made me look like I'd never seen a boiler before.
Checkpoint: Read the model number. Cross-reference it with the installation manual. Confirm whether you're dealing with a Burnham condensing boiler or a standard Burnham gas boiler. This takes two minutes and saves you from wasted diagnostic time.
Step 2: Photograph the thermostat wiring before replacement
Thermostat replacement is one of those jobs that looks simple until you're staring at a nest of low-voltage wires and realizing you didn't label anything.
I learned this the hard way in September 2022. A property manager needed a thermostat swap done before a tenant move-in. I had about two hours to get it done, so I skipped the photo step—normally I'd document every wire, but there was no time. Went with what I thought was the standard R-W-G-Y configuration based on the old thermostat's layout. Powered it up, and the system short-cycled immediately. I'd mixed up the common wire.
That error cost $140 in a return trip plus a very annoyed property manager. Now I photograph the wiring block before disconnecting anything. Every single time.
Checkpoint: Take a clear photo of the terminal labels and wire positions. If you're replacing a smart thermostat, verify the C-wire requirement against the boiler's control board. Don't assume the old setup will map cleanly to the new one.
Step 3: Test the blower motor under load, not just visually
Here's a mistake I see repeatedly, and I made it myself early on: checking the blower motor by watching it spin and calling it good. A blower motor can spin freely by hand and still fail under load.
What I do now:
- Check amp draw against the motor nameplate rating
- Inspect the capacitor—a weak capacitor will let the motor start but cause it to overheat
- Listen for bearing noise with the motor running
- Check the blower wheel for debris buildup (I've pulled out everything from drywall dust to a small bird)
Checkpoint: If the blower motor draws more than 10% above nameplate amps, dig deeper. Don't just assume it's fine because it's spinning.
Step 4: Check the condensate trap and drain line on condensing models
On Burnham condensing boilers, the condensate trap is a common failure point. If it's clogged or dry, you'll get lockouts, pressure switch errors, or water backing up into the combustion chamber.
I once skipped this check on a routine maintenance visit because the boiler was running fine at the moment. Three weeks later, the customer called with a no-heat complaint. The trap had plugged with debris, the pressure switch tripped, and the boiler locked out. That $85 service call turned into a $340 repair because I didn't spend five minutes checking the trap during the maintenance visit.
Checkpoint: Remove the trap, flush it, and verify the drain line flows freely. If the trap is dry, check for a blocked vent or an incorrect slope on the drain line.
Step 5: Inspect the heat exchanger and combustion chamber
This is the step most technicians rush through. I get it—it's dark, awkward to access, and usually nothing's wrong. But "usually" isn't "always."
On Burnham gas boilers, look for:
- Carbon buildup or soot on the heat exchanger surfaces
- Cracks in the casting (especially around the burner ports)
- Water stains or rust that suggest a gasket failure
On condensing models, also check the secondary heat exchanger for scale or corrosion. If you find anything borderline, document it with a photo and note it on the service ticket. Don't just mentally mention it—write it down. I've had two cases where a "probably nothing" heat exchanger observation turned into a warranty claim six months later, and the only reason we had any leverage was because I'd documented it.
Step 6: Verify gas pressure and check for leaks
Standard procedure, but easy to skip when you're in a hurry. Check inlet and manifold gas pressure against the boiler's data plate. A boiler running at the wrong manifold pressure will either underfire (sooting up the heat exchanger) or overfire (shortening component life).
Use a combustion analyzer if you have one. If you don't, get one. I don't say that often, but for Burnham equipment—especially condensing units—you need to see the CO and CO2 readings, not just guess based on flame appearance.
Step 7: Check the expansion tank and system pressure
Low system pressure causes more nuisance lockouts than almost anything else I see. Check the expansion tank charge with a tire gauge. If it's waterlogged, the system pressure will swing wildly between cold and hot states.
I've seen techs skip this because "the boiler was running when I got there." Running doesn't mean healthy. Check the cold-fill pressure against the boiler's recommended range (usually 12-15 psi for residential systems, but verify against the manual).
Step 8: Confirm warranty documentation and registration status
This is the step that most people ignore—until they need it. Burnham's warranty terms are specific about what's covered, what's excluded, and what documentation is required for a claim.
Per FTC guidelines on warranty disclosures (16 CFR Part 700), written warranties must be clearly labeled as "full" or "limited" and must state the terms in understandable language. That's the minimum. The practical reality is that warranty claims get denied for missing purchase receipts, unregistered installations, or service records that don't match the manufacturer's requirements.
I keep a simple checklist for every Burnham install we touch:
- Is the warranty card mailed or registered online?
- Is the original install invoice on file?
- Have all service visits been documented with dates and findings?
If the warranty card still needs to be mailed, USPS First-Class Mail postage effective January 2025 runs $0.73 for a standard letter (per usps.com/stamps). It's cheap. What's expensive is a denied claim because nobody sent the card in.
Step 9: Log everything and set the next service date
The last step is the one that protects you. Write down what you found, what you fixed, and what you recommend for next time. Include photos when possible.
I created our team's pre-check list after the third rejection in Q1 2024—three warranty claims denied in a single quarter because the service records didn't align with the manufacturer's maintenance requirements. Since implementing the checklist, we've caught 47 potential documentation gaps in the past 18 months. That's 47 claims that didn't get denied.
Common Mistakes and Things to Watch For
A few things I've seen—and done—that don't fit neatly into the steps above:
Don't mix up appliance maintenance schedules. I've had junior techs ask about cleaning procedures for ice maker machines while standing in front of a boiler (if you're actually searching for how to clean an ice maker machine, check the appliance manual—it's a different system entirely). The discipline of regular cleaning is the same, but the steps and chemicals are not. Boiler cleaning and ice maker cleaning share zero overlap beyond the word "cleaning."
Don't chase the cheapest part. Aftermarket blower motors and thermostats exist, and some of them are fine. But on Burnham condensing boilers, the control board is sensitive to voltage fluctuations and communication errors. I've seen cheap aftermarket thermostats cause lockouts that disappear the moment you put an OEM unit back on. The $60 you save on a thermostat isn't worth three return trips.
Don't assume the last tech did it right. I've walked into service calls where the previous technician "fixed" a pressure switch issue by jumping out the switch entirely. That's not a fix—that's a safety hazard. Verify what you're looking at before you build on it.
And don't skip the paperwork. Looking back, I should have started documenting service visits from day one. At the time, it felt like busywork. But given what I know now—how many warranty claims hinge on a single missing service record—that "busywork" is the cheapest insurance you can buy.
The bottom line: Burnham equipment is reliable when it's installed and maintained correctly. The failures I see are almost always process failures, not product failures. Follow the checklist, document what you find, and don't assume anything is fine just because it was running when you pulled into the driveway.