The Question Most Buyers Ask Wrong
"Should we fix it or replace it?"
I get this question probably twice a month. And honestly, most people asking it are framing it wrong. The real question isn't about the equipment. It's about what happens when it stops working.
I manage facilities purchasing for a 200-person company across three buildings—roughly $180,000 a year in equipment, maintenance contracts, and repairs. When I took over purchasing in 2020, I started tracking every repair decision in a spreadsheet. Equipment type, age, repair cost, what happened next. After two years, the patterns were impossible to ignore.
Here's what I found: the right answer depends almost entirely on what breaks if the equipment goes down. Not the age. Not the repair quote. The consequence of failure.
So I sort every equipment decision into one of three buckets: mission-critical, seasonal, and high-use-but-low-stakes. The advice is very different for each. Sometimes the opposite of what you'd expect.
Scenario A: Mission-Critical Equipment (Boilers)
If the equipment failing means people can't work, the decision is almost always repair—fast. Cost is secondary. You can negotiate the invoice later. You can't un-send 200 people home.
We run a Burnham commercial boiler in our main building. When the pilot light went out last January, I didn't ask "how much to fix it." I asked "how fast can someone be here." A cold building means the entire office sends people home. That's not a repair decision. That's an emergency.
But here's what I learned after the second time it happened: most Burnham gas boiler pilot light issues aren't boiler failures at all. They're thermocouple or ignition problems. The parts—once you actually pull up a Burnham boiler parts list—are cheap. Usually under $150. The expensive part is getting a qualified technician out there, and that's where transparency matters more than price.
One service company quoted me a $400 diagnostic fee, then said the thermocouple was "another $350 installed." A second company quoted $125 for the diagnostic and $180 total for the repair. Same part. Same time window. The difference was how they structured the quote.
"I've learned to ask 'what's NOT included' before I ask 'what's the price.'"
Here's something vendors won't tell you: diagnostic fees are often negotiable—or waivable—if you proceed with the repair. They don't want to lose the job over a fee they can absorb. Ask. The worst they can say is no.
For mission-critical equipment, pay for speed and competence. But make them itemize. Diagnostic fee, parts, labor, after-hours premium. If they won't break it down, that silence tells you something.
Scenario B: Seasonal Equipment (Snow Blowers)
This is where the "always repair" instinct gets expensive.
We have an EGO snow blower for our parking lot and entry walkways. Two winters ago, the auger stopped turning. My first instinct was to fix it—it was only three years old, and a replacement was $600. Why replace something that's practically new?
The repair quote was $280. Plus $75 pickup and delivery. That's $355 to fix a machine we use maybe six times a year. I paid it.
And then the battery pack started failing the next winter. Another $200.
I only believed that seasonal equipment rarely justifies repair after paying $555 total on a $600 machine. Cost-per-use on that snow blower was over $45. A new unit would've been $50 per use for the first year—with a fresh warranty.
Most buyers focus on the repair quote and completely miss the cost-per-use calculation. For equipment you use a handful of times per year, repair rarely makes financial sense. Especially battery-powered tools, where the battery is half the value and degrades whether you use it or not.
Scenario C: High-Use, Low-Criticality Equipment (Ice Makers, Condensers)
This is the trickiest category, and it's where most of my purchasing mistakes happened.
Our break room has a countertop ice maker. It gets used constantly—probably 80 times a day. When it started making cloudy ice, my first thought was replacement. But a colleague asked when we'd last cleaned it. The answer was... never?
I looked up how to clean countertop ice maker units and realized the whole thing took 20 minutes with vinegar and water. The "problem" was scale buildup. Zero dollars to fix. The machine was fine.
Same story with our condenser units. One of the HVAC techs pointed out that a dirty condenser coil can make the whole system work 30% harder—burning electricity and shortening equipment life. Cleaning it is routine maintenance, not a repair. Replacing it is a $4,000 mistake that a $200 cleaning would've prevented.
So for high-use equipment, exhaust the maintenance checklist first. Cleaning, descaling, filter changes, coil brushing. I've saved more money on equipment that didn't need replacing than on any negotiation I've ever done.
How to Tell Which Scenario You're In
Answer these four questions before you authorize any repair or replacement:
- What's the downtime cost? If the equipment going down for a day costs more than the repair, fix it now and sort out the invoice later.
- What's the cost-per-use? Divide total cost (purchase + repairs + maintenance) by how often you actually use it. High cost-per-use on low-frequency equipment usually means replace.
- Have you done the maintenance? Be honest. If the answer is "not recently," do that first. You'd be surprised how many "broken" machines just need a cleaning.
- Will the quote survive contact with finance? If the vendor won't itemize, assume the worst. A clear $500 quote is almost always cheaper than a vague $350 one—because the vague one grows.
One more thing. None of this works if you're not tracking repairs. I keep a simple spreadsheet—equipment, age, repair history, cost per repair. After two years, the patterns are obvious. You don't need fancy software. You need to know which machines are quietly draining your budget.
Look, I'm not a technician. I don't know the inside of a boiler from the inside of a snow blower. But I know how to ask the right questions and how to read a quote. Most of the time, that's enough.